Sustainable Design: Bins
Office: 2699 Tigertail Avenue, #54, Miami, FL 33133
Sustainable Design: Planters
Your design calls for a series of planters to line the parapet wall on a rooftop, or to create a barrier around a space.
Or you need to fill a BIG space, but you don't want a built-in planter, because you will need future access for roof maintenance.
We created our Multi-Section Planters for just those situations and they will last decades longer than Fiberglass backed by a Lifetime Structural Warranty.
We combine our proprietary trademark Mariner corner with our Mariner T-leg to join lengths of wood, recycled plastic lumber or other materials to build the size you need.
For long, narrow planters, we install a frame to support the liners. For larger, deeper planters, the wooden box is a facade around self-supporting liners.
We've built many one-sided facades for permanent installation along walls—why spend money on a beautiful planter wall that no one will see?
Our multi-section planters are more cost-effective than the same number of individual planters because they require less material.
We can design the planters to use a combination of less expensive standard molded liners, although custom liners are always an option.
The planters can ship flat on a pallet, for lower shipping costs, and they typically take 10-15 minutes per section to assemble. A typical installation of over 400 linear feet of planters in Manhattan was completed in just three days.
Most multi-section planters are shipped with pre-assembled end sections, the joining planks and angles are added on site to speed installation further.
Our 21.5” height multi-section planters, with panels on all 4 sides, run about $230-$245/linear foot for recycled plastic lumber, and $260-280 for solid hardwoods, including commercial-grade molded plastic liners. For 31.5" height multi-section planters add approximately 20-25%.
Differential height Mariner extrusions, shown below, used for garden planters can create back panels out of many materials including wood, for privacy and access control, or even glass to create windbreaks for outdoor restaurants.
DeepStream's liner-inside-a-planter-box design, and proprietary trademark marine-anodized aluminum legs, ensure the lowest cost of ownership over time. Our planters are backed by a Lifetime Structural Warranty.
The liners prevent the soil from contacting the wood, and the air space between insulates the root-ball so it doesn't get warmer than the ambient air.
While enjoying your outdoor wood planters keep in mind that drainage is critical to the health of your plants grown in containers, and it is very difficult to remedy after the fact. Generally more "tended" plants die from drowning than from lack of water. "Old School" drain holes on the bottom and "gravel" drainage medium simply do not work and will quickly clog.
DeepStream pioneered modern drainage practices with side-wall drains and 3-layer drain packs. DeepStream places from one to three 3/4" threaded drainage ports on its 12 stock proprietary plastic planter liners, to which various plugs, hose barbs and valves may be attached. Liners are non-structural and are meant to be placed inside planter boxes.
Depending on your plants, planting mixture, and local weather, you may need to add more drains. Additional drain holes can be added as required by drilling additional holes in the side walls. DeepStream installed drains are centered about 2" above the bottom to allow the clay "fines" in planting mediums that are responsible for clogging to settle to the bottom.
Standard ABS liners and custom-welded liners come without drain holes, but they may be drilled as required. Reservoir liners come with one drain port, and more cannot be added.
If your planters will not be dug up and replanted every year then we strongly recommend adding Drain Filter Packs for each drain.
A three-part filter combines the waffled plastic backing of TREMdrain, three layers of filter fabric, and Biobarrier buttons to inhibit root growth.
They may not stop aggressive root systems like Bamboo and Clusia.
Filter packs, when used in conjunction with clean 1-2 mm inorganic drainage material to slow the flow of the water to the drain, could prevent clogged drains for a decade or more.
DeepStream Designs will, in case of damage or an unacceptable degradation in finish, replace any metal component, plastic caps, plastic feet, lid retaining straps, bungee cord, and most other components of our products at manufacturer’s cost, plus shipping, for any planter box we make. All components of our products are recyclable, so under this program, major components, such as aluminum legs and stainless steel lids must be returned to DeepStream for recycling. Please call Sheila at 305-857-0466 to make arrangements for replacement parts.
The aluminum extrusions, stainless steel lids, and fasteners used in planters that DeepStream manufactures are guaranteed for the life of the structure against defects in manufacturing, materials and workmanship. Our multi-section planter frames are guaranteed for life against structural defects.
The panels made from rigid materials or fabrics are the customer’s selection and retain the manufacturer’s warranty for those materials, which will vary by manufacturer. We will be happy to provide warranty information for products and components that we do not manufacture.
Aluminum extrusions and stainless steel fasteners have been used in the yachting industry for decades. The etched marine anodized finish of the aluminum extrusions is a durable finish, created especially for coastal environments (Alumilite 215/A41 with surface preparation C22). The 3/4" tropical hardwoods we select have been used in exterior applications such as docks, decks and boat construction for centuries. These woods have decades of life expectancy, although they can be affected by mold, mildew, dry rot and drying.
The primary failure for wooden planters is the joining of wood components to each other. Wood has been used for centuries to split stone because of its tendency to expand when wet. DeepStream has designed its products with heavy aluminum extrusions to join these components in such a way that allows the wood to expand and contract naturally to withstand the test of time. We assemble these products using a proprietary bedding compound in the wood for screw holes to prevent rot, and proprietary dielectric paste for stainless steel fasteners to aluminum extrusions to avoid galvanic action that can cause them to seize over time.
Environmental conditions and maintenance, or lack thereof, will affect the life expectancy of the finish of our products, and as such, no warranty is given on the finish, but we do offer the Core Replacement Program to assist in keeping our planters, recyclers and structures looking fresh.